Search Results

Natural gas has been considered as an alternative fuel for a heavy duty diesel engine with its lower pollutant and carbon dioxide emissions than its counterpart. However, due to the high auto-ignition temperature of methane, this alternate fuel has been mainly used in spark-ignited engine with relatively lower compression ratio, losing full potential of achieving high efficiency. To overcome these limitations, high-pressure direct injection of the natural gas in a compression ignition engine has been proposed, and there have been several attempts to understand physical behaviors and ignition of methane jet. In this study, auto-ignition characteristics of high-pressure methane jet were investigated both through the experiment and the multi-zone modeling to suggest the applicability to such engine.

This paper presents an integrated control of in-wheel motor (IWM) and electronic limited slip differential (eLSD) to enhance the vehicle lateral stability and maneuverability. The two actuators are utilized in the proposed controller to achieve separate purposes. The IWM controller is designed to modify the understeer gradient for enhanced handling characteristic and maneuverability. The eLSD controller is devised to improve the lateral stability to prevent oversteer in a severe maneuver. The proposed controller consists of a supervisor, upper-level controller and lower-level controller. The supervisor determines a target motion based on a target understeer gradient for IWM control and a yaw rate reference for eLSD control. The upper-level controller generates a desired yaw moment for the target motion. In the lower-level controller, the desired yaw moment is converted to the control inputs for IWMs in the two front wheels and eLSD at the rear axle.

Improving fuel efficiency and emission characteristics are significant issues in engine research. Because the engine has complex systems and various operating parameters, the experimental research is limited by cost and time. One-dimensional (1D) simulation has attracted the attention of researchers because of its effectiveness and relatively high accuracy. In a 1D simulation, the applied model must be accurate for the reliability of the simulation results. Because in-cylinder turbulence mainly determines the combustion characteristics, and mean flow velocity affects the in-cylinder heat transfer and efficiency in a spark-ignited (SI) engine, a number of sophisticated models have been developed to predict in-cylinder turbulence and mean flow velocity. In particular, tumble is a significant factor of in-cylinder turbulence in SI engine.

This paper describes the ground system model and algorithm for a ground level simulation tool. First, the modeling of an automotive ground system will be discussed and the algorithm for a simulation tool will be explained. We divided the model into a ground tree and a ground body. The ground tree model consists of resistance formed by the wires that connect the load to ground point with various structures and the ground body model consists of resistance between ground points in the car body. The wires with large current, such as engine ground cable, was modeled in detail by dividing the resistance into wire, bolt, and clamping resistance, in order to simulate the effect of increased contact resistance after durability test. The algorithm of the ground level simulation tool was designed to adjust the currents of the alternator, battery, and ground points in order to evaluate the various driving and load conditions.

The volumetric efficiency for a 4-stroke, single- cylinder, spark- ignition engine is considered. The mathematical model for the gas exchange process was formulated and solved by numerical technique. The mass flow rate, the pressure-time history in cylinder, intake and exhaust pipes, and the volumetric efficiency were calculated. The important parameter affecting volumetric efficiency was the pressure in the pipes. But, the effect of valve timing on volumetric efficiency was small (1, 2)*. The experiments with 3-different cams were performed. The predicted results were compared with experimental data and satisfactory agreement was obtained. As a result, the volumetric efficiency could be predicted with a relatively simple mathematical model.

This paper presents a stability monitoring algorithm with a combined slip tire model for maximized cornering speed of high-speed autonomous driving. It is crucial to utilize the maximum tire force with maintaining a grip driving condition in cornering situations. The model-free cruise controller has been designed to track the desired acceleration. The lateral motion has been regulated by the sliding mode controller formulated with the center of percussion. The controllers are suitable for minimizing the behavior errors. However, the high-level algorithm is necessary to check whether the intended motion is inside of the limit boundaries. In extreme diving conditions, the maximum tire force is limited by physical constraints. A combined slip tire model has been applied to monitor vehicle stability. In previous studies, vehicle stability was evaluated only by vehicle acceleration.

This paper presents a methodology of trajectory planning for the surrounding-aware lane change maneuver of autonomous vehicles based on a data-driven method. The lateral motion is planned by sampling candidate patterns which are defined based on quintic polynomial functions over time. Based on the cost evaluation among the sampled candidates, the optimal lateral motion pattern is selected as a reference and tracked by the controller. The longitudinal motion is planned and controlled using Model Predictive Control (MPC) which is an optimal control method designed considering the surrounding traffic information. To realize the lane change motion similar to the human driving behavior in the surrounding traffic situation, the human driving pattern is modeled in the form of motion parameters and considered in planning the lateral and longitudinal motion.

The powertrain of an automatic transmission has a wide operating range in speed, torque and temperature while driving. It is necessary to know them to achieve good shift quality in various operating conditions without tuning the parameters of the shift quality controller. All but the torque sensor is installed in the automatic transmission because of its high cost. In this study, a more precise algorithm is suggested for estimating turbine torque using a neural network model that has three inputs, i.e., engine speed, turbine speed and temperature. The performance of the suggested turbine torque estimation algorithm is validated through experimental results. To utilize the estimated turbine torque in shift control, a shift control algorithm, which shows good shift quality in various operating conditions, is developed.

The flame propagation characteristic is one of the greatest factor that determines the performance of spark ignition (SI) engines. The in-cylinder flow dynamics is very significant in terms of flame propagation because of its direct influence on the flame shape, turbulent flame speed, and the ignition quality. A number of different techniques are available to optimize the in-cylinder flow and maximize the utilization of turbulence for faster combustion, and tumble enhancement by intake port geometry is one of them. It requires excessive computational expenses to evaluate multiple designs under wide range of operating conditions by 3D-CFD, therefore, a low-dimensional model would be more competitive in such design optimization process. This work suggests a new modification approach for typical 0D turbulence model to take account for the tumble generation during the intake process as well as the turbulence characteristics associated with it.

This paper presents an Interacting Multiple Model (IMM) based side slip angle estimation method to estimate side slip angle under various road conditions for vehicle stability control. Knowledge of the side slip angle is essential enhancing vehicle handling and stability. For the estimation of the side slip angles in previous researches, prior knowledge of tire parameters and road conditions have been employed, and sometimes additional sensors have been needed. These prior knowledge and additional sensors, however, necessitates many efforts and make an application of the estimation algorithm difficult. In this paper, side slip angle has been estimated using on-board vehicle sensors such as yaw rate and lateral acceleration sensors. The proposed estimation algorithm integrates the estimates from multiple Kalman filters based on the multiple models with different parameter set.

This paper proposes a rear-wheel steering control method that can modify and improve the vehicle lateral response without tire model and parameter. The proposed control algorithm is a combination of steady-state and transient control. The steady state control input is designed to modify steady-state yaw rate response of the vehicle, i.e. understeer gradient of the vehicle. The transient control input is a feedback control to improve the transient response when the vehicle lateral behavior builds up. The control algorithm has been investigated via computer simulations. Compared to classical control methods, the proposed algorithm shows good vehicle lateral response such as small overshoot and fast response. Specifically, the proposed algorithm can alleviate stair-shaped response of the lateral acceleration.

A spark-ignition engine commonly induces tumble flow because it generates high turbulence, which is a crucial factor in determining the flame propagation speed. Since tumble affects not only the flame propagation speed but also the various in-cylinder phenomena, it predominantly determines the performance of the engine. In that sense, many studies have been conducted to investigate tumble. Although various studies have revealed the characteristics of tumble numerically and experimentally, there has been no research to identify the physical mechanisms of these characteristics. Although some studies specified the mechanisms from an angular momentum perspective, the theory was insufficient to explain the entire phenomena of tumble. Hence, this study attempts to comprehend the fundamental causes of tumble phenomena such as ‘spinning up’ and ‘vortex breakdown’ from the perspective of kinetic energy.

To properly respond to demands to reduce national energy consumption and meet greenhouse gas emission targets based on environment policy, the Ministry of Trade, Industry, and Energy of Korea formed a research consortium consisting of government agencies and academic and research institutions to establish the first fuel efficiency standards for medium- and heavy-duty (MHD) commercial vehicles. The standards are expected to be introduced in 2017 as Phase 1 of the plan and will regulate trucks with a gross vehicle weight in excess of 3.5 tons and buses with a carrying capacity of more than 16 persons. Most MHD commercial vehicles are custom-made and manufactured in diversified small-quantity batch production systems for commercial or public use, resulting in difficulties in utilizing mandatory vehicle tests for fuel efficiency evaluations.

This paper describes a failsafe system of automated driving vehicles. The failsafe system consists of the following two parts: sliding mode observer-based environment sensor, chassis sensor fault detection, and emergency deceleration control. Two sliding mode observers are designed to reconstruct the fault of acceleration and environment sensor(Lidar) in a longitudinal direction. In the environment sensor's fault detection part, the longitudinal vehicle model receives clearance and relative velocity values. Therefore, failure diagnosis is possible regardless of environmental sensors, such as radar, lidar, and camera. This paper's sensor data is the failure of Delphi's Electronically Scanning Radar (ESR) and Ibeo's LUX Lidar installed in an autonomous vehicle. The emergency deceleration control algorithm employs the sliding mode control with adaptive convergence time. In the event of a failure, it is significant to control the vehicle within a short period safely.

This paper describes a lateral control of autonomous large size buses on road with large curvature. In the case of long and wide commercial vehicle such as large bus, applying centerline tracking controllers in constrained environments such as large curved road (e.g. turning at intersection) may cause some concerns. Two concerns are considered: inner lane crossing related to collisions with curb and opposite lane crossing related to threatening surrounding vehicles. Considering relations between width and curvature of the road and length and width of the large size bus, the curvature of road at which inner or outer lane crossing begin to occur was calculated when centerline tracking controller was applied. Thus, the proposed algorithm optimizes motion of the bus by using model predictive control (MPC) using road geometry as constraints.

As global emission standards are becoming more stringent, it is necessary to increase thermal efficiency through the high compression ratio in spark-ignited engines. Various studies are being conducted to mitigate knocking caused by an increased compression ratio, which requires an understanding of the combustion phenomena inside the combustion chamber. In particular, the in-cylinder flow is a major factor affecting the entire combustion process from the generation to the propagation of flames. In the field of spark-ignited engine research, where interest in the concept of lean combustion and the expansion of the EGR supply is increasing, flow analysis is essential to ensure a rapid flame propagation speed and stable combustion process. In this study, the flow around the spark plug was measured by the Laser Doppler Velocimetry system, and the correlation with combustion in spark-ignited engines was analyzed.

Regulations regarding vehicles’ CO2 emissions are continuing to become stricter due to global warming. The CO2 regulations urge automobile manufacturers to develop gasoline engines with improved efficiency; however, the main obstacle to the improvement is the knock phenomenon in spark-ignition engines. If knock is predicted, the efficiency potential can be maximized in an engine by applying modest spark timing. Several research regarding knock prediction modeling have been conducted, and typically Livengood-Wu integral model is used to predict the knock occurrence. For the prediction, knock onset should be determined on a given pressure signal of given knock cycles for establishing the 0D ignition delay model. Several methodologies for knock onset determination have been developed because checking all the knock onset position by hand is impossible considering the breadth of data sets.

This paper describes a hierarchical motion planning and control framework for overtaking maneuvers under racing circumstances. Unlike urban or highway autonomous driving conditions, race track driving requires longer prediction and planning horizons in order to respond to upcoming corners at high speed. In addition, the subject vehicle should determine the optimal action among possible driving modes when opponent vehicles are present. In order to meet these requirements and secure real time performance, a hierarchical architecture for decision making, motion planning, and control for an autonomous racing vehicle is proposed. The supervisor determines whether the subject vehicle should stay behind the preceding vehicle or overtake, and its direction when overtaking. Next, a high level trajectory planner generates the desired path and velocity profile in a receding horizon fashion.

This paper describes vehicle stability control (VSC) scheme to prevent rollover and to improve both maneuverability and lateral stability by integrating individual chassis control modules such as electronic stability control (ESC), active front steering (AFS) and continuous damping control (CDC). The proposed VSC system consists of an upper and lower level controller. The upper level controller determines a control mode such as rollover mitigation, maneuverability and lateral stability, and it also calculate desired values for its objectives. The lower level controller determines longitudinal and lateral tire forces as inputs of each control modules such as the ESC and AFS. From the simulation results, it is shown that the proposed VSC system can prevent vehicle rollover, while at the same time improving both maneuverability and lateral stability

This paper presents a longitudinal control algorithm for an adaptive cruise control (ACC) with collision avoidance (CA) in multiple vehicle traffic situations. The proposed algorithm consists of a multi-target tracking filter, a primary target selection algorithm and an integrated ACC/CA system. The multi-target tracking filter is used to smooth the sensor signal, and makes it possible to apply to a control system. The primary target selection algorithm decides an in-lane target and provides the information to an integrated ACC/CA system in order to drive a subject vehicle smoothly and improve safety in complex traffic situations. Finally, the integrated ACC/CA system computes the desired acceleration. The performance and safety benefits of the multi-vehicle ACC/CA system is investigated via simulations using real data on driving. Simulation results show that the response of multi-vehicle ACC/CA system is more smooth and safer at a change of traffic situations.